application of central dust collector How to set the dust cover? from khedmehcom's blog

application of central dust collector Because the filter material is folded into a cylinder, the filter material layout density is large, so the dust removal mechanism is compact and the volume is small; The height of the filter cartridge is small, the installation is convenient, and the maintenance workload is small; The filter area of the same volume dust collector is relatively large, the filter wind speed is small, and the sniper is not big; Filter material folding requires strict sealing at both ends and no air leakage, otherwise it will affect the dust removal effect. The filter drum type dust collector is composed of air inlet pipe, air exhaust pipe, box, ash hopper, ash cleaning device, filter barrel and electric control device. The filter cylinder in the dust collector arrangement is very important, the filter cylinder can be vertically arranged in the dust collector box flower plate, can also be inclined arranged on the flower plate, fixed with bolts, and with rubber pads, the lower part of the flower plate is divided into filter chamber, the upper part is divided into clean gas chamber, the filter cylinder treatment is fixed with bolts, the convenient method is automatic locking device and rubber compression device, these two methods, It is convenient for installation and maintenance. The tilt Angle of the dust hopper should be fixed according to the rest Angle of the dust, and generally should not be less than 60 degrees. The discharge valve of the cartridge dust collector should be tight. The height of the clean air chamber of the filter should be convenient for the installation and maintenance of the pulse injection device.

The structure of the central dust collector is composed of an air inlet pipe, an air exhaust pipe, a box, a ash hopper, a ash cleaning device, a diversion device, an air flow distribution plate, a filter cartridge and an electronic control device, which is similar to the dust removal structure of an air box pulse bag. The arrangement of the filter cylinder in the dust collector is very important, which can be vertically arranged on the box flower plate or tilted on the flower plate, and the vertical arrangement is more correct from the ash cleaning effect. The lower part of the flower plate is the filter chamber, and the upper part is the air box pulse chamber. An air flow distribution plate is arranged at the inlet of the dust collector.

The following describes how to set the dust cover of the application of central dust collector:

First, the use of external dust exhaust cover, in the lower part of the cover as far as possible to install enclosures to reduce the scope of dust suction.

Second, the setting of the dust collector can not hinder the operation and maintenance.

3. The dust containing air flow controlled by the dust collecting hood does not pass through the operator's breathing zone.

4. If conditions permit, a closed cover should be used as far as possible to separate the dust from the operator and limit it to a local area.

5. When installing the receiving external dust exhaust cover, the direction of vacuuming should be consistent with the direction of dust particle ejection.

6. When setting the external dust exhaust cover, the cover mouth should be as close as possible to the place where the dust occurs.

The application of central dust collector is composed of air inlet pipe, air exhaust pipe, box, ash hopper, ash cleaning device, diversion device, air distribution plate, filter cartridge and electronic control device, similar to the air box pulse bag dust collection structure. The layout of the application of central dust collector is very important. It can be arranged vertically on the box flower plate or tilted on the flower plate. The vertical layout is more correct from the ash cleaning effect. The lower part of the flower plate is the filter chamber, and the upper part is the air box pulse chamber. An air flow distribution plate is arranged at the inlet of the dust collector.

dust collector is widely used in cement, steel, power, food, metallurgy, chemical and other industrial areas, the overall capacity increased several times, becoming a filter area > 2000m2 large dust collector (GB6719-86 class), It is a solution to solve the problem of the old-fashioned dust collector, which is difficult to collect dust, the filter wind speed is good, the dust cleaning effect is poor, the filter bag is easy to wear and leak, and the operation cost is not low. Compared with the existing bag type and electrostatic precipitator on the market, it has the characteristics of large filter area, low pressure difference, low emission, small volume, good service life, etc., which has become the new direction of the development of industrial dust collector.

application of central dust collector https://www.kaisenfilter.com/Central-Dust-Collector


Previous post     
     Next post
     Blog home

The Wall

No comments
You need to sign in to comment